For Sale - PCM - 4394 - Injection Moulding Machine Futura Series

-Futura系列机器的特征是

一个。在很大程度上提高了总体注入成型效率水平
b。它是由最节能的伺服机制驱动的，可节省最高的能源，一致，可重复和更平滑的机器性能
C。与常规液压机相比，节能约20％至60％

-Clamping
一个。Sturdy and optimized five-point double otggle system, known for its quick mould open and close movements along with its good mould safety characteristics; is one of the most preferred clamping mechanism in the world
b。Moving platen supported on machine base with adjustable sliding shoes
C。自润滑灌木丛以进行切换机制
d。Automatic, motorized mould height/thickness adjustment through Sun and Planetary gear mechanism
e。带有压力开关反馈和低级传感器的高级，进行性型自动润滑油润滑
f. Water resistant stainless steel supporting tracks for moving platen
G。Hard chrome plated, high tensile steel tie bars
H。Stress-relieved sturdy machine base frame
一世。Closing and opening speeds, pressures and positions independently settable. Each programmable in 05 stages
j。Linear position transducer for accurate clamp position control

-ejector
与多个中风。中央水力喷射器feature. Speed, pressure and position independently settable in both directions
b。脉动以及弹出器保持/保持向前功能
C。Linear transducer for accurate ejector position control
d。Multi point ejector plate for uniform force distribution provided with multiple ejector rods

-Injection
一个。Wide choice of injection units with A/B/C screw/barrel combinations
b。Injection speed and pressure profile programmable in 06, position dependent stages
C。跟进/保持压力曲线可在05中编程的压力曲线，依赖时间阶段
d。螺钉速度控制轮廓可在05中编程，位置依赖阶段
e。强与平衡的双缸注入单元沿螺丝中心线平均分配负载/压力
f. High torque, low speed direct hydraulic screw drive
G。Proven screw geometry for optimum plasticizing capacities with excellent melt homogeneity
H。通过控制器的反向压力，配置文件可编程在位置依赖阶段
一世。Fitted with nitrided screw and nitrided barrel, non-return valve and barrel closure assembly with open nozzle suitable for various thermoplastics
j。Delay feature for commencement of plasticizing to aid processing of engineering plastics
H。Monitoring of melt cusion during the follow-up/hold-on pressure phase
一世。Switch over from fill to pack based on position or time
j。线性位置换能器以进行准确的注射位置控制
k. Suitable capacity material hopper with easy sliding arrangement

-温度控制
一个。4/5的4/5自优化温度控制区/电路，带有陶瓷加热带，用于枪管和喷嘴法兰加热系统
b。PID controlled barrel heater bands, with solid state relays and fast blowing semi conductor fuses for barrel heating system
C。可调节的高/低公差带，用于监视，并警报偏离设定点
d。工作温度范围高达450度C
e。热夫妇分解警报

-Controls
一个。具有大型TFT，多色显示屏的智能操作员机器接口，带有Alpha数字键盘
b。Actual position measuring/indicating system for moving platen, screw travel and ejector
C。Overview screen with live display for machine operations
d。Continuous process control via monitoring of important process parameters with selectable tolerance band
e。USB上的数据存储
f. Internal storage of upto 200 sets of mould data
G。重要参数以及小时生产数据监控
H。Built-in energy management with live display of voltage, current and energy
一世。实时显示瞬时功率，每小时能量监控，持续30天
j。带有自动开关关闭功能的镜头（成型）反选项
k. Fault diagnostics in the event of machine malfunction or operator error with plain text messages and recording of source of error
l。Regulated power supply 24VDC for controls and actuators
m. I/O diagnosis - analog & digital

- 溶解作用
一个。Highly energy efficient hydraulic drive system with gear pump & servo motor
b。Ergonomically designed easy to access and easy to service hydraulic circuit layout
C。快速响应液压门安全互锁
d。Large capacity heat exchanger for hydraulic oil cooling
e。Core pulling control set for hydraulic cores independently programmable
f. All hydraulic manifolds and valves mounted close to the actuators for faster response
G。Ergonomically designed, easy to access and easy to service hydraulic circuit layout Energy saving "pump switch off feature" in case of idle running

-一般的
一个。符合人体工程学设计的机器盖和门，以安全性，优雅的哮喘患者
b。具有防振动垫的灵活机器支撑
C。Set of electrical output - single phase (1 X 16A) and 3 phase (1 X 32A) sockets
d。Water battery with inlet and outlet temperature indicator

-Optional features
一个。用于液压核的其他核心拉力控制集，可独立编程用于顺序或并行操作
b。带有气阀的空气爆炸在移动的板条上
C。Air blast with pneumatic valve on fixed/stationary platen
d。旋转芯（液压螺旋）界面
e。Electrical un-screwing interface
f. Robotic arm interface (Std.or Euromap -12)
G。Photo sensor arrangement for molded part drop detection, recommended for single cavity
H。用极限开关向后验证模具弹出器板的接口
一世。附加喷嘴加热器带的接口
j。特殊螺钉，以更好地融化均质化和增塑化
k. Special design screws for specific engineering polymers like PC, Nylons, PET, RPVC, CPVC, etc
l。耐磨/耐腐蚀，双金属螺钉和桶，用于加工磨料/腐蚀材料
j。较高增塑速率k的液压电动机。保存节能加热器带
l。Water battery with flow rate control
m. Accumulator for higher injection rates
n. Built-in 6 zones, HRTC; expandable up to 12 zones

For More details:

Electronica Plastic Machines Ltd
电话号码+91 020-66933535
Email:enquiry@electronicapmd.com