Required - PR - 1579 - FIBC Bags for Food

我们是世界上跨国公司领先的食品公司之一。我们的全球采购单元正在寻找Fibc袋的制造商。

Manufacturer must have AIB (American Institute of Baking) certification, Metal detection capability and well-equipped testing facility.

General Bulk Bag Specification: -

- 监管要求：该成分应符合粮食等级，包括标签，符合1938年的《联邦食品，毒品和化妆品法》，并根据经修订的所有适用法规

- 犹太洁食：不违反犹太洁食要求

- 针头控制要求：所有散装袋制造商都必须制定针对针对制造的每个针的针头控制程序，以与被处置的暗针和破碎的针的数量。

- 金属探测要求：所有散装袋制造商都应具有能够检测2 mm 316不锈钢球的金属探测器

- Bag Foot Print Dimension: Each bag shall have a footprint of 35 inches by 41 inches. The Height of the bag will vary depending on the density of the ingredient and the requirements. Maximum height 55 inches

——安全评级:袋是满足最低安全rating of 5:1.A. Filled bag weighing 2400 lbs is to be capable of withstanding a 12,000 lb static force without failure when bag is suspended by its four lifting loops. Bags may not be reused.

- Lifting Loops: The bag will have four lifting loops. One loop will be located on each of the four corners of the bag. Lifting loops must be constructed of 2-inch wide polypropylene webbing with a minimum tensile strength of 5000 lbs.

Defining Characteristics Of General Bags: -

- 袋尺寸：面板尺寸在袋子GMI名称中定义，并将在接缝之间以英寸为单位进行测量。袋子尺寸应印在袋子制造商识别标签上，该标签应缝在袋子的接缝中。

- Document Pouch: The bulk bag supplier shall attach two 11 x 15 inch clear documentation pouches, which are no smaller than 11 x 15 inches to each bag. Each pouch shall be sewn onto the center of the bag, 10 to 12 inches below the top seam, on two adjacent sides. On bags taller than 65 inches, the pouch shall be sewn 40 inches from
顶缝。该袋应预先密封三个侧面。第四侧应具有自密封功能，并应位于小袋的短侧。袋应水平放在袋子上，顶部的长边缘。缝合应在袋顶部的1/2英寸内。

- Bag Fabric: The fabric shall be white woven finless polypropylene. The sides, bottom and the protective flap on the port hole bags are to be 5.0 to 6.5 ox/sq yd and the tops are to be 3 oz/sq yd. The fabric may have either a double strength band running the length of the bag or be folded double for strap attachment. Bags must conform to ASTM testing and methods for tensile strength, Mullen burst strength, trapezoid tear strength, percent elongation, and puncture.

- UV Resistance: Bags are to be constructed from polypropylene fabric containing inhibitors for resistance to ultraviolet deterioration. The bag fabric must retain not less than 70% after 1200 hours of exposure in a weather meter in accordance with Method 5804 of Federal Standard 191.

(The loops shall not fail in advance of the fabric). The length of the loop above the bag will be 8 inches, minimum; at its apex from the bag when filled and empty. The color of the loops is not specified. There shall be a 1 to 1 1/2 inch wide webbing band, with a 2500 lb bursting strength, around the top perimeter of the bag for reinforcement.

- Fill Spout: The fill spout shall be 16 inches in diameter and not shorter than 24 inches. The Spout shall be constructed of a minimum of 3 oz/sq yd white, woven polypropylene and attached to the top panel with a folded seam with the stitching to the outside of the bag. The spout shall have a simple unfolded side seam with stitches to the outside. The spout's free end must be either over edged, heat-sealed or other wise secured from fraying. A tie ribbon must be attached to the spout 4 to 6 inches above the top of the bag.

- 顶部：顶部应为3盎司/平方英尺。YD白色，编织的聚丙烯，并连接到侧面板上，并带有折叠的接缝，缝线到外部，零褶。

- 侧缝和底部接缝：使用60磅的断裂强度聚丙烯线或双重缝线使用2600 denier高密度（> 7.5克/denier）聚丙烯多丝线线，应将侧缝和底部接缝一起缝合在一起。侧缝和底接缝具有紧密缝线的填充胶带（又称垫圈，偏见），以防止内容物零褶筛。（胶水不用于填充褶。）填充
Tape is not required in the seams of the port hole. All edges are to be folded over and double stitched.

- Porthole Requirements: Porthole diameter shall be a minimum of 20 inches. The edges of the port will be folded and stitched, (heat cut port holes are not permitted) A 6 mil panel of polyethylene whose edges shall be folded and sewn into the bottom seams is to cover the inside bottom of the bag. The liner shall be only one thickness to allow for a clean penetration during discharge.

- All ingredients shall be contained within the bounds of the bulk bag (i.e. the liner and ingredient shall not herniated through the port hole)

- Porthole Flap Requirement: Porthole style discharge bags with an unattached shall have a protective flap covering the entire bottom (diaper) of the bag, which shall be tied in place during storage and transportation. The bag shall contain four polypropylene tie back loops. Two loops shall hold the flap in place during shipment and storage. Two loops shall be placed in the side seams at the appropriate height to allow the protective flap to be tied back during discharge.

- Discharge Spout Requirement: Shall be made of a minimum of 3 oz/sq yd white, woven polypropylene fabric.

- Spout shall be double-walled to provide protective draw ribbon cover in one piece construction. The draw ribbon must be tacked to the bag.

- 袋子的底部和侧缝的吐口附件应为简单的接缝，缝线到外部。