净瞬时out提及的网络宽度
类型 |
Web width |
厚度 |
Speed |
净生产 |
|
毫米 |
Micron |
Mt/1’ |
kg/h |
拉紧 |
1500 |
15 |
413 |
500 |
拉紧 |
1500 |
17 |
363 |
500 |
Features of the rolls produced:&nb = sp;
-3 x500毫米
- 1 x
- OD
&= nbsp;&nbs = p;&= nbsp;&nbs = p;&= nbsp;&nbs = p;
Cooling capacity:
- 280.000 Kcal /hr
- Water chiller excluded from the supply, if required to be quoted separately= .
电力:400 V +/- 10%-50 Hz三相 +N +G
线组成
挤压组撰写= d:
n°1单scr = ew挤出机
- 通过弹性接头连接到挤出机变速箱的电动机
- AC motor
- 带法兰泵和冷却系统的挤出机变速箱
- 带加热器加热桶;一个独立风扇的空气冷却每个区域。
- Barrel and screw made of nitrided alloy steel.
- 螺钉是双飞行屏障类型
- Feed zone jacketed for water cooling.
- 带有视力玻璃,排空斜槽和低水平警报的颗粒料斗
- 包括颗粒装载器
- 车轮上的挤出机底架。
n°2Single scr= ew extruder
- 通过关节连接到挤出机变速箱的电动机
- AC motor
- 带法兰泵和冷却系统的挤出机变速箱
- 带加热器加热桶;一个独立风扇的空气冷却每个区域。
- Barrel and screw made of nitrided alloy steel.
- 螺钉是双飞行屏障类型
- Feed zone jacketed for water cooling.
- 带有视力玻璃,排空斜槽和低水平警报的颗粒料斗
- 包括颗粒装载器
- 车轮上的挤出机底架
n°3适配器sy =茎挤出机并死亡
- 手动屏幕更换器。
-n°2熔体压力表后和之前和之前和之前。
-n°1熔体温度量表。
第1号手册扁平= mm.2050的死亡
适合挤出热塑性材料;演员电影
With the following specifications:
- 上唇:
Manual flexible adjustable through push thermal block every
- Lower Lip:
用适合开放范围的土地固定。
- Manifold:
使用计算机流仿真的操作数据MA = DE介质的Coathanger分布通道预先计算出来。
为了验证性能保证,客户必须在名义工作温度和剪切速率下提供粘度cu =适用聚合物的rves在10秒至1000 sec-1之间。
- 结构:
重型体重,高输出,高压或非常宽的模具;
- 死亡加热:
由特殊的弹药筒加热器恰当地分组为区域,并连接到=多极连接器。
该模具可以开放,以清洁而无需拆卸接线系统。
每个区域都有用于热电偶的钻孔。
- Wiring of thermo bolts
包裹在不锈钢接线盒中,并在板上的多极插头上接线。
通过管道冷却,客户必须为管道的EA = CH侧提供压缩干空气。
Technical data:
- 嘴唇宽度:
- 嘴唇差距可调节:0,1至
- Output: 800 kg/h of LLDPE
- 入口:矩形
- Zones number: 7
- 手动调整螺栓:80
- 电压:220/240 V.
- 热电偶孔:M 12 x 1,5 x 15轮辋。9
- 电气连接通过:板上的多极插头
第1号黑匣子ca = st with 3 pos。:
- Coextrusion Black Box with feed block made for cast lines, with fan shaped entries, interchangeable insert for possible layers sequency exchange, plate with convergent passages on the outlet section, with three position pin for programmed combination of the layers;
- 备用处女销,以允许通过改变通道的形式来定制用其产品制成的图层配置文件;
- Heating by flat heaters outside opportunely arranged.
Technical data:
- 条目/层:3
- Main entry: B vertical in center
- 卫星入口侧:右 /左
- Layers sequence: ABC
n°1挤出机=和模具支撑:
由钢制成,配有托架用于线性扩展的额外补偿= ders
铸造部分:<= o:p>
该单元由支撑结构组成,其中有两个通过拉杆连接的钢重侧侧框架,以具有坚固而坚固的结构。
所有的铸造单元都安装在马车上,水平移动在轨道上。
N°1主寒意寒意滚动直径。
800 mmequipped with= a special water circulation system that guarantees an uniform surface temperature. The roll surface ischromed plated, grinded and polished. Chill roll is perfectly balanc= ed either statically or dynamically. To obtain a film uniform cooling on all t= he roll transversal surface, the same is equipped with a cooling internal cham= ber with a forced differentiated water with multiple and parallel channels. All= the internal surfaces near the cooling water are produced with a special anti-r= ust treatment. At one end of the roll the rotating joint to connect casting uni= t to water feeding flexible hose is foreseen. Roll is furnished with a AC.motor = at variable speed, driven by inverter. To grant security during emergency stop chill is provided with an electro pneumatic disk brake. Main casting roll is provided with a cleaning steel roll whose external surface is covered with silicone with spiral grooves. Cleaning roll is installed on oscillating lev= ers controlled by pneumatic cylinders for the contact with the main roll. Clean= ing roll pressure contact is adjustable.
n°1次级=寒冷卷寒意滚动直径。
由铝制成的怠速传输卷,具有硬化的外表面和SPE = CIAL饰面,以避免横向滑动膜。卷卷以高光滑度在滚珠轴承上组装。
n°1空气sucti =在刀片上(真空盒)板钢机构,与模具无关的调节,机械设计结合了易于维护和清洁,通过拆分室设计。所有不锈钢结构。
Adjustable blades are provided at the pre sweep section and between pre sweep and prim= ary chamber. Smoke collecting manifold with suction control shutter Each chambe= r is designed with a suction manifold connected to a suction fan with speed adjustment by inverter.
吸入风扇速度调节和弯曲度的抑郁程度是根据冷却组的操作员面板上设置的值和/O = R的基础设置的,并且在监督系统上考虑要产生的膜类型,厚=相同的ESS和生产速度。
注意:所有自由=从寒冷卷到绕线器的滚动均受硅的保护,用于防粘材料。
n°2 edge Keepi =高速静电设备
n°1振荡框架with continuous movement+/- =
n°1 nip roll b = web分离的绕线器之前
N°1 Automatic = winder mod. GAP 1500
结构钢框架,配有平整螺钉。
几个钢肩,被横块连接在一起,并被保护面板覆盖。=
铝怠速卷。
带有气动开放/关闭的几个nip,由电子控制的交流电提供动力。电动机还原器。
n°2inner longitudinal blades and= N°2 lateral longitudinal blades for scraps.
毫米统治者注册纵向切割。
带有特殊表面图案的绕组卷,由A.C.电动机还原器
气动橡胶涂层压力卷。
用于滚动和绕组之间的压力控制的液压系统
抗固定条。
滚动单元,由电动机运营。
每米和每直径更改。
n°1横切。
几只武器。
由电动机降低器动力的几个轴支架臂从绕线机到接收台排放。多亏了此系统,轴在工作周期中仅需f = ew秒即可为更改做好准备。
可变速度轴发射单元。
n°2个纸板芯的气轴。
电动轴装载机。
控制面板。
事故预防警卫。
光学和声音警报以及紧急按钮
n°1中的sc =说唱恢复系统
2个吸力管,1个喷油管,1吹动的边缘吸力带有沉默的bo = x,1个带有有机玻璃盖和检查面板的料斗,1个碎屑交换阀F =或通过1grinder单位,带沉默盒的1grinder或维护目的用沉默盒,1 Cyclon。
n°1碎片rec = overy挤出机直径。
Nitrided barrel.
Treated steel screw.
交流电机
Rossi Motoriduttori制造的电动机还原器(平行轴)
N°1 thermoregulation zone by means of armoured heaters and controlled by thermocouple.
N°1 melt temperature gauge.
水冷却饲养区。
带有检查门和抗固定条的特殊料斗。
Steel frame
Water mixing tank = and pumps:
Mixing tank capacity 5000 lt , N°4 delivery pumps complete with 3-way valves , manifold for delivery/return , connection pipes to the machine not included=
注意:水冷却器排除在外。
N°1厚度控制系统供应商NDC
Complete with :
8000TDI操作=系统<= o:p>
8000TDI软件设计用于易用性,同时为用户提供=键和关键显示,以使其能够运行和操作生产线。
NDC型号8000 TDI扫描厚度表和显示软件和Hardwa = RE平台包括桌面操作员工作站(OWS)
Single Board Computer (Embedded PC) running Embedded Windows CE™ Operating System
专用操作系统提供安全的操作环境,操作员只能访问测量系统功能,系统基本上免疫病毒,troj =马,蠕虫和其他基于“ Instant O = n”操作的强大软件闪光灯
Features
- Recipe storage
- 高级条纹检测
- 自动屏幕打印
- Roll defect mapping
- 多语言显示
- 与植物网络兼容
- 可选速度,左右和中心区域MD控件
- 可选的SPC/SQC
- 可选的OPC或DDE双向通信与主机计算机
Infrared transmiss= ion sensor for film thickness measurement
FG710是最先进的传感器之一high-precision measurement of film thickness and is rapidly replacing more traditional sensors, such as K= r85 beta transmission, for this measurement. Whilst the FG710 is not appropriate for customers running black (carbon black loaded) films it can be used with= out major problems for other coloured films including TiO2 and CaCo3 loaded fil= ms. One of the powerful features of the 710 series of sensors is that it can be fitted with up to 10 filters providing NDC with a Virtual Real Spectrum that enables us to analyse and then remove the influence of pigments and fillers. Colours typically found in medical applications such as blue, green and pink can also be accommodated for by the sensor. It is insensitive to humidity, barometric pressure, or gap temperature.
Features
- 高测量精度
- 快速响应时间
- 测量许多类型的聚合物
- High tolerance to changes in ambient condition and web flutte
minitrak-o框架s =罐头<= o:p>
When it comes to making precise scanners to assure the cross-web performance of = our extremely accurate sensors, NDC Infrared Engineering excels. With its new MiniTrak scanning family, we continue this trend.
Minitrak-O框架是为小网设计的(
控制柜:
- 加热,控制,提供控制挤出机的区域,并通过PLC进行加热。
- 驱动系统:挤出机的交流驱动器。
Drive is engineere= d, mounted, wired, and provided with appropriate protection; Main chill roll , second chill roll , in let nip roll on the winder , trimming nip roll , win= ding drum电动机还原器
- 控制站=用于寒冷滚动,绕过PLC - 受控功能:绕组速度,TENS =离子,液压单元,自动切割设备,仪表计数器,带有控件和读数的远程安装封闭。
- 用于挤出机的本地面板,上下移动,向前中进的移动,开始吹动气刀和运动调整的起步,用于真空刀的起点,与Winder的控制柜接口,用于从偏远位置控制Winder。
- Pressure and temperature indications with LDC display with: first "sound alarm"= ; on primary threshold, "second shut down alarm" on secondary pressure threshold
-Photocell和li = MIT,Prossimity开关。